|
 |
|
 |
T-KJr2 140,000 Btu Indoor Tankless Water Heater, NG |
|
 |

Click to enlarge |
 |
Takagi Tankless Water Heater
T-KJr2 140,000 Btu Indoor Tankless Water Heater, NG
Takagi T-KJr2-IN Tankless Water Heater is the smallest water heater in the Takagi tankless line with gas inputs up to 140,000 BTU per hour and an energy factor of 0.81-0.83. This cost-efficient and environmentally friendly Takagi Tankless Water Heater can support hydronic baseboard or radiant floor heating applications, as well as provide domestic hot water to plumbing fixtures and appliances. Takagi T-KJr2-IN can meet all the hot-water needs of a small American home or apartment with one or two bathrooms.
At an average (rise in temperature) of 60F in warmer areas Takagi T-KJr2-IN Tankless Water Heater will provide 228 GPH (3.8 GPM) and enough hot water for one shower and a lavatory basin at a time; or one low-flow shower (2.5 GPM or less) and an appliance, such as a dishwasher or washing machine, at the same time. In colder areas where the input temperature may be 40F or less you can expect a flow rate of about 174 GPH (2.9 GPM) and running only one major fixture at a time. Please refer to the flow charts for specific rates. The All new Takagi T-KJr2-IN has a max GPM of 6.8GPM.
Takagi Tankless Water Heater T-KJr2-IN has four preset temperatures: 113F, 122F, 131F, 140F.
To achieve any temperatures other than those presets, use the Takagi TK-RE02 remote temperature controller.
To convert the water heater from a standard vent system to a direct?vent (or sealed combustion) system, use a Direct?Vent Conversion Kit. By default (indirect vent), the unit will use the intake air from the room where it is installed.
T-KJr Features:
- Fully modulating, gas fired tankless water heater
- Indoor installation only(Direct-vent convertible)
T-KJr Safety Features:
- Air-Fuel Ratio (AFR) sensor
- Exhaust & Water Temperature Safety Control
- Overheat Cutoff Fuse
- Internal Freeze-Protection System
- Manual reset high limit switch
- Horizontal or Vertical Installation
T-KJr Specifications:
- Fuel Type: Propane
- Max BTU Rating: 140,000 BTU/h
- Min BTU Rating: 19,500 BTU/h
- Max. Flow Rate: 6.6 GPM (Gallons Per Minute)
- Min. Flow Rate: 0.75 GPM (Gallons Per Minute)
- Water Pressure: 15 ? 150 psi (40 psi or above is recommended for maximum flow)
- Energy Factor (NG): 0.82;
- Capacity: 2 fixtures (at 60F or higher inlet water temp.) or 1 fixture (at 40F inlet water temp.)
- Hot/Cold Water Connections: 3/4" NPT
- Gas Connection: 3/4" NPT;
- Weight: 33 lbs
- Dimensions (inches): 20.25" high x 13.75" wide x 7.75 " deep
- Electric Consumption: 120 VAC ; Standby: 0.05 A, Operation: 0.61 A, Freeze-Protection: 0.93 A
- Ignition: Electric Ignition
- Propane Inlet Pressure: 8.0" W.C. min.; 14" W.C. max
- Manifold Presure (Propane): 2.5" W.C.
- Temperature Settings (dipswitch settings without remote controller): 113F, 122F, 131F and 140F
- Temperature Range (with TK-RE02 Remote Control): 99 - 167F
- Venting Intake: 3" O.D. (ABS, PVC, Galvanized Steel, Corrugated Stainless Steel or Category III/IV Stainless Steel);
- Flue/Exhaust: 4" O.D. (Category III Stainless Steel)
- Vent: 50' Max Length, 5 elbows max
|
 |
Get a 10% Tax Credit with any Takagi Water Heater Installation with a Energy Factor >= 0.82
For more information see Takagi's website: Takagi Tax Credits/Rebates |
For more information, view:
|
Part Number: T-KJr2-IN-NG
|
|
|
|
|
|